During normal use or even during hanging, a door and its frame may develop several defects.

A binding door
If the hinge side of a door comes into contact with the frame before the door is fully closed, it is probably because the hinges have been sunk too far into the door or frame. A door in this condition is said to be hinge bound. A door may also become hinge bound if the screws project out of their countersinks and stop the hinge closing fully.

This problem can be cured cither by packing out the hinge in its recess – use materials such as sandpaper, card, card¬board or hardboard – or by driving the screw fully home. In the latter case, new screws which are smaller than the original ones may be the best solution.

Insert packing beneath the hinges to cure a hinge-bound door. Protruding screws should be replaced

A sticking door
Occasionally a door may stick when it comes into contact with the frame through too much paint on the door and frame or, in the case of external doors, because the wood has swollen.

The simplest solution is to plane off a sufficient amount of wood to allow the door to close freely. Take the wood off the door, not off the frame – it is much easier. The door may have to be removed to get at the top and bottom. Take care not to overdo planing down external doors that are damp. The door will shrink when it dries out and a large gap will be left if too much is taken off.

When a door which has to pass over an uneven floor catches the floor over the high spots, you should locate the problem places on the floor, put sandpaper over them and pass the door over the sand¬paper a few times.

A sagging door
Doors usually sag because the hinges have been pulled out of the frame or door edge, or because the hinges have been strained. Hinges often work loose when a door is hinge bound. To resecure the hinges you can:

• use longer screws
• use thicker screws – size 10s instead of 8s, for example, so long as the hinges have holes and countersinks large enough to accommodate them
• insert pieces of dowel into the screw holes before putting the screws back in.

A problem with strained hinges usually means that the hinges were not big enough – a pair of 75mm hinges will generally hold an internal door, but a heavy external one may need three 100mm hinges.

With boarded and panel doors the swinging (lock) stile – the one opposite the hinges – may drop so that the door bottom catches on the floor as you open it. This sag in the frame can usually be attributed to one of two causes.

Loose joints
In framed doors – panel and boarded – the joints occasionally work loose. To resecure them, cut new wedges for the ends of the tenons and bore two holes through the stile and the tenons to take pieces of dowel. Glue the wedges and dowel firmly in place. If the tenon is broken in the mortise hole, bore two holes down the tenon into the rail and glue pieces of dowel in place to strengthen the joint.

Poor bracing
Framed boarded doors need to be properly braced. A door that is not adequately braced – because its braces are at too shallow an angle, say – has no braces, or has its braces the wrong way round will sag. Braces should have their lowest point at the swinging stile.

A ledged-and-braced door with adequate bracing. Note that the braces hold up the non-hinged side of the door

Article Source: http://EzineArticles.com/?expert=Tauqeer_Ul_Hassan

For most home owners, a screen door is an excellent way to provide a barrier between yourself and the annoying objects that fly in to bother you from the outside world. This of course includes insects which seem to never stop bothering you no matter how busy you are and despite how many swats you’ve taken at them. And even though bugs are the main culprit and source of frustration, random objects like leaves and pine needles are also sometimes blown in from out doors. But in addition to these benefits, some home owners also want a feeling of security that standard screen doors simply cannot provide. They want to be able to rest in their homes with a feeling of comfort while their families to remain safe at night when they sleep in their beds. For this commendable need, home owners should purchase a security screen door.

A security door is built from a much heavier material than normal, ensuring a very sturdy barrier between yourself as well as your possessions and whatever person is trying to break their way in. Fastened with special bolts and clamps onto the front part of the door are steel grilles, which are used to reinforce the door and provide extra strength. These special grilles can also be made out of cast iron or a different type of strong metal. The grilles are close enough together to provide the strongest protection, but allow enough room for sunlight to reach through the glass or wire mesh that lies beneath them.

The hinges on the security door will also be made of much stronger metals then other models, very similar to the grilles which are welded securely into the exterior. With all of this metal being used on this door, one might wonder just how disruptive the iron and steel will be to the eye. You needn’t worry though, as many models of security screen doors can be very decorative, even when providing that extra layer of protection for your home. While more pleasing models are available, it is advisable that you seriously weigh the options of your purchase and decide if you value a more decorative design over a safer home when choosing your model.

Upon review, the added benefits of this model of screen door will provide you with extra security that you otherwise wouldn’t have. This added protection is something that will help you and your family sleep easier at night, so if you’re serious about needing a more secure home, a security screen door is an excellent choice.

A garage door is really one of the most important safety features you can do for your home or office. It’s not just a way to keep your vehicle out of the rain and snow. It’s an important access point that some people take for granted. If you’re going to spend money on this important part of your home, you want to make sure you get the right size door for your garage.

Measuring Made Simple

You’ll want to measure the door height and width. Since most standard doors are in even feet, that is 8 feet by 9 feet, you can use a yardstick. If you try and gauge the size with by “eyeballing” it, you could really have a problem if your “eyeball” isn’t calibrated right!

Standard Sizes

There are a few sizes of doors that are considered standard. These include 8 x7 feet, 8×8 feet, 8×9 feet, 9×8 feet, 10×7 feet, and 10×8 feet for single car garages. For double doors, the standard sizes are 12, 14, 16, and 18 feet by 7 feet and 12, 14, 16, and 18 feet by 8 feet. You can also order a custom size, but expect to pay much more.

What Other Measurements Are Needed?

You’ll also want to measure the sideroom and the headroom. This will help in determining what type of track and hardware can be installed. Most will require at least 3 ¾ inches on each side of the door and 5 ½ inches at the top. However, each manufacturer may have their own specifications. Make sure you know what these are for the type of door that you are considering.

DIY or Professional Installation?

This will depend on your skill level as a handyman! If you are going to do the install yourself, you’ll need to ensure you have the proper tools. You’ll also need someone to help you, as the door is rather large, heavy, and cumbersome. A professional may be the answer you need if the garage door sizes are custom made or very large, such as a triple door. You don’t want to try and put the door up yourself, only to have it crash down in the middle of the night!

In Closing

Since so many of the garage door sizes today are standard, there’s a pretty good chance you’ll be able to find a good deal. However, for custom doors, you can expect to pay at least twice as much and installation could cost you more as well.

If you have dogs or cats, you quickly learn how convenient a pet door could be. Especially with cats, there’s the constant open the door, shut the door. When they’re out they want in, and when they’re in they want out. Why wear out your door hinges and sliding door when you can give your pet the freedom to leave and enter your home at their leisure? Installing a pet door is a relatively inexpensive thing to do, and depending on the type you install, can be done in an hour or so.

Here are a few different options you have when it comes to installing a door for your pet.

Sliding Glass Door Attachment

One of the least expensive and easiest way to give your pet the freedom he or she wants is buy installing an addition to your sliding glass door. These are sold as vertical glass slats that vary in width depending upon the width of the pet door you need. You install it into the sliding glass door tract and it sits next to the original door. This addition has a pet door built in. You only need to seal the gap between the addition and the original door, as well as bolt the original door into place to keep it from opening. That is the only downside to this method – it almost renders the exit useless, except for by your pets.

Pets Doors Within a Door

If you don’t want to take the drastic step of cutting a hole in your wall and installing a traditional pet door, consider instead installing one into an interior door. Many homeowners will do this in the door leading to the garage, and then leave the garage door open. This serves a couple functions: it allows you some control of when your pet can leave the home, yet allows the animal access to food, water and bedding which may be located in the garage. It also doesn’t affect the resale value of your home, as a door can be inexpensively replaced.

Cutting a Hole in Your Wall

The most permanent and drastic way to install a pet door is by having one put into a wall that leads to the exterior of your home, preferably a fenced side or back yard. There are easy to follow instructions on most DIY websites, but you will need to cut a rectangular hole in your wall to allow for the installation of the door. Be sure to check wiring and plumbing locations before you begin tearing your wall apart.

If you’re still unsure whether a pet door is right for your animals, remember that there are styles that will allow only authorized pets through, keep wild critters out and your pets safe.

The garage is now considered as the main entrance and exit in a household. It is no longer just a place to store your cars and other junk but a place where your children can go to and play sometimes. Also, some put up a family room in their garage door so making it as secure as it can be is crucial.

Tell you what, there is an easier way for you to see to it that the opener of the door of your garage is in too functioning. Let me share with you some insightful tips on how to keep it running smoothly.

Tip 1: Inspect the track for anything that is not aligned well or for any loose parts. If you notice loose screws or misaligned tracks, immediately act on it. Straighten the parts and secure the loose areas.

Tip 2: Test your operator. If it sounds squeaky, it may need a bit of cleaning or some parts may be rusty. This is especially true if you are using chain-driven door openers. Replacing the rusty parts is important rather than just leaving it there to rot. It will be more dangerous if you leave unstable openers of the door of your garage to rot. If you think it just needs a little cleaning, you can buy a machine sprayer or oil and apply it on the tight areas.

Tip 3: Run the garage door operator and place your hand on the beam laser detector. It should be able to detect that it is about to crash into something. In this case, the door of your garage should open up simultaneously. If this does not happen, then there is something wrong about its sensor. Consider getting a replacement.

Tip 4: Change key codes every now and then. You can reboot the whole system of the door opener once in a while to ensure its top functioning. You can also get a keyless wireless keypad so that you can change codes as often as you want to ensure total safety. Make sure the locks still work perfectly fine inside. Some brands offer dual lock system.

These simple tips can help you keep your garage door in top functioning. If you want to prevent garage door mishaps, make sure you spare some time in maintaining it.

Interior designing has undergone considerable changes over the years and today the rules and styles that govern the whole concept of interior designing have also changed a lot. Interior designing is basically the styling or the designing of the interiors of a space to make it more aesthetic.

One new style that has come into the field of interior designing is to utilize small but useful little components and build a look around them. Thus small components like an antique clock or a door handle are incorporated into a room and then the entire look is developed around that item. This concept is a very unusual one but one which can be an absolute revelation if developed the right way.

Doors have been much neglected objects as far as interior designing is concerned. Not a lot of interior designers give much thought to decorating a door. This in turn works against making a house look complete and are a detriment to the aesthetic appeal of the house.

However the attitude towards doors is slowly changing and a lot of people are decorating doors with ornate door handles, polished knockers and many more things. Handles as a decorative aspect have garnered a lot of popularity and a number of interior designers are utilizing these handles as decorative elements for doors.

A door handle is been increasingly used as a starting point for a particular theme or for developing a particular theme. A well placed and well selected can be used in such a way that an entire theme can be developed and applied to a particular room. Illustrating with an example would provide our readers with a more clear understanding of the concept.

An Edwardian door handle or a handle with a burnished back plate can be used on a door of a room or can be given a very central placement in the room. Once the component is placed in the room then the entire look of room can be designed in accordance with Edwardian sensibilities and this look will complement the room perfectly as every item in that room is in tune with the particular era which it is representing.

Today most houses in the world are constructed keeping in mind the modern angle and also the modern mindset of the world. In such settings the conventional antique door handles can stick out like sore thumbs and will not work in enhancing the look and feel of the particular house.

Thus using modern door handles is the best choice. However not every modern handle is hastily and flimsily made. If an individual looks carefully for the right handle then there are a number of handles which are made with stylish chrome finishing who can provide a very sharp and stylish look to the house. There are also a number of which are available in various shapes and these if used well in the interior designing can give a very different and wacky look to a room. Using a brass knocker as a door handle can be a unique way of decorating a door, however this brass knocker should be placed on the center of the door.

1. A wood door mat saves you more money in the long run. Though it is relatively costly than plastic doormats, wooden door will spares you from buying replacements as it is hard-wearing and is able to last for a long time. Because it is very effective in trapping and taking away harmful particles from your shoes or sandals and keeps your house clean and your family healthy, you don’t have to buy expensive air purifiers and dehumidifiers.

2. Wood door mat is time saving. Because it is made up of wood, less foot prints and fewer dusts will accumulate on it, less bacteria and viral particles can cling on it or get inside your house. It will require you very few minutes to clean it, you can clean this mat by sweeping off dusts and spraying some antibacterial cleansers.

3. A wood door mat can safe guard your health. About half of the dust that tries to get inside your home on the shoes of your family and friends is trapped by a wood door mat, among these dusts are cold and flu viruses and fungal and viral particles. Kids or babies are very vulnerable from these harmful particles. Symptoms like breathing complications and nasal are often caused by bacterium and viruses that travel in the air. Thus, having this type of mat on your door way will keep you and your family members healthy.

4. You can never go wrong with wood door mat as it can fit in all types of terrain. People that live on higher grounds or rural areas won’t have to worry about bigger dirt and dusts that is often turned into mud by rainstorms. People in urban areas don’t need to worry about oil, liquid spills, gum, etc., that might get inside their house. Hardwood doormats are very effective in trapping all kinds of unwanted dusts and particles and keeping your house’s floor clean even from you doorway.

Any homeowner looking to spice up the entrance way into their home should be looking into a wooden screen door. They are elegant and show off fine detail in their craftsmanship, all while offering the same excellent perks of a regular model of this special kind of door, plus many others that aren’t matched by the latter door. Being able to enter your home from your porch through a well designed and classy wood screen is a great perk that many property holders would love to enjoy.

When your home has a wood screen door installed you will be receiving protection from the standard outside interferences, such as annoying little creatures like bugs and insects, as well as the infrequent bunches of dead leaves that fly in via random gusts of wind. Both of these annoyances will be solved when you have this type of door in place between your home and the outside world, providing a solid barrier between the two.

Most of the types of woods you can select for your door to be custom built are very elegant and beautiful types. In most cases, the most common types of finished materials will be Douglas fir, red cedar, poplar and pine as well as mahogany and red oak. Even though these are the most common, other kinds can be substituted as well. It’s in your best interest to view the woods in person and compare them with the surrounding materials of the house it will be installed on for the best suitable match. It would be an unfortunate incident if you chose a specific type of wood and once it was installed you did not like it.

Another great benefit is that you can install a pet door inside of the wood screen door so your furry loved ones are able to move in and out as they please. This is a priceless add-on as it eliminates your need to get up throughout the night to let your pets in and out for the bathroom.

These are the main benefits to owning a wooden screen door, and as you can see, there are plenty. If you’d like to add a piece of classy, beautiful furniture to your home or walk way, this product is definitely for you.

Background Information

Mail slots have been a beautiful addition to the front doors of many homes and businesses in the United States since the mid nineteenth century when the post office determined it would be a more efficient means of delivering letters to residents when they were not home. Prior to this, a post man would need to wait until the home or business owner answered the door to receive their letters and this wasted (according to the post office) at least an hour and a half of time each day simply waiting. By installing a slot (or sometimes letter box) in the door, this allowed the post man to drop off letters any time of the day for residents to receive when they returned home. Although they are less common now, a solid brass mail slot is still a wonderful way to complete any front entryway set and is still used in many residential neighborhoods.

Choosing a Mail Slot

Mail slots are available in a variety of designs and finishes but a solid brass construction is an important feature because this ensures strength and durability over time. These slots typically have an exterior flap to protect against weather and an optional interior flap. If you are using a pre-existing hole in your door make sure that you choose a mail slot that will fit – not all mail slots are the same size so check the overall measurements and the measurement of the opening. They are available in a variety of finishes including Polished Brass, Antique Brass, Polished Chrome, Brushed Nickel and Oil Rubbed Bronze.

Whether you are installing a mail slot for the first time or replacing an older one, it is a great opportunity to update the overall appearance of your front door and create a new and exciting theme. Coordinate your mail slot with your existing hardware or replace your older door knob sets, doorbells and knockers with coordinating patterns. By using a common finish for all these items you can create a common theme without needing to use the same pattern and/or design. Accenting your new hardware with a dramatic lion door knocker or coordinating kick plate can complete completely change the look of your door without needing to replace it.

Where to Shop

LookInTheAttic & Company offers a wide selection of beautiful front door hardware including mail slots, knockers and kick plates and they offer free design assistance and help. Search for a solid brass construction and be sure to ask questions like what is the internal opening measurement or is this item available in any other finishes? The front door is the focal point of the exterior of your house and a great opportunity to reflect your unique personality.

Once the entire bottom frame member is cut off to shorten the door, the bottom piece that was cut off must be reinserted to close the door cavity.

1) After removing the door from the hinges. Calculate the thickness of the finished floor covering and add 3/4 inch to that measurement.

2) Transfer that measurement to the bottom of the door. Measure both bottom ends and scribe a line across the whole width of the door. ( Use a sharp utility knife).

3) Measure the distance from the end of the circular saw guide-plate to the blade.

4) Now transfer this measurement and make a mark on both ends of the door exactly from the scribed mark and clamp a straight edge. The straight edge will serve as a guide for the circular saw to rest against while sawing.

5) Saw off bottom of the door. The hollow core of the door might be exposed after the cut is made. If this is the case, you will need to replace the bottom frame.

6) To replace the bottom frame, chisel the veneer off the cut-off frame, cut it to fit tight between the side frames of the door. Apply glue to both sides of the cut-off frame and insert it into opening. Wipe off excess glue and let dry preferably over night.